Since there are ways to alter the configEpoch outside of the failover
procedure (for exampel CLUSTER SET-CONFIG-EPOCH and via the configEpoch
collision resolution algorithm), make always sure, before replacing our
configEpoch with a new one, that it is greater than the current one.
SET-CONFIG-EPOCH, used by redis-trib at cluster creation time, failed to
update the currentEpoch, making it possible after a failover for a
server to set its configEpoch to a value smaller than the current one
(since configEpochs are obtained using currentEpoch).
The bug totally break the Redis Cluster algorithms and protocols
allowing for permanent split brain conditions about the slots
configuration as shown in issue #1799.
There is a time defined by REDIS_CLUSTER_WRITABLE_DELAY where fail -> ok
switch is not possible after startup as a master for some time, however
the contrary (ok -> fail) should always be possible.
Thanks to this change, when there is some code like:
clusterDoBeforeSleep(CLUSTER_TODO_UPDATE_STATE|...);
... and later before returning to the event loop ...
clusterUpdateState();
The clusterUpdateState() function will clar the flag and will not be
repeated in the clusterBeforeSleep() function. This especially important
for config save/fsync flags which are slow to execute and not a good
idea to repeat without a good reason.
This is implemented for all the CLUSTER_TODO flags.
The new command is able to reset a cluster node so that it starts again
as a fresh node. By default the command performs a soft reset (the same
as calling it as CLUSTER RESET SOFT), and the following steps are
performed:
1) All slots are set as unassigned.
2) The list of known nodes is flushed.
3) Node is set as master if it is a slave.
When an hard reset is performed with CLUSTER RESET HARD the following
additional operations are performed:
4) A new Node ID is created at random.
5) Epochs are set to 0.
CLUSTER RESET is useful both when the sysadmin wants to reconfigure a
node with a different role (for example turning a slave into a master)
and for testing purposes.
It also may play a role in automatically provisioned Redis Clusters,
since it allows to reset a node back to the initial state in order to be
reconfigured.
The previous code handling a lost slot (by another master with an higher
configuration for the slot) was defensive, considering it an error and
putting the cluster in an odd state requiring redis-cli fix.
This was changed, because actually this only happens either in a
legitimate way, with failovers, or when the admin messed with the config
in order to reconfigure the cluster. So the new code instead will try to
make sure that the keys stored match the new slots map, by removing all
the keys in the slots we lost ownership from.
The function that deletes the keys from the lost slots is called only
if the node does not lose all its slots (resulting in a reconfiguration
as a slave of the node that got ownership). This is an optimization
since the replication code will anyway flush all the instance data in
a faster way.
Using CLUSTER FAILOVER FORCE it is now possible to failover a master in
a forced way, which means:
1) No check to understand if the master is up is performed.
2) No data age of the slave is checked. Evan a slave with very old data
can manually failover a master in this way.
3) No chat with the master is attempted to reach its replication offset:
the master can just be down.
Automatic failovers only happen in Redis Cluster if the slave trying to
be elected was disconnected from its master for no more than 10 times
the node-timeout value. However there should be no such a check for
manual failovers, since these are initiated by the sysadmin that, in
theory, knows what she is doing when a slave is selected to be promoted.
The error when the target key is busy was a generic one, while it makes
sense to be able to distinguish between the target key busy error and
the others easily.
The same change was operated for normal client connections. This is
important for Cluster as well, since when a node rejoins the cluster,
when a partition heals or after a restart, it gets flooded with new
connection attempts by all the other nodes trying to form a full
mesh again.
Initially Redis Cluster accepted that after cluster creation all the
nodes were at configEpoch 0, evolving from zero as failovers happen.
However later the semantic was made more strict in order to make sure a
cluster has always all the master nodes with a different configEpoch,
which is more robust in some corner case (especially resulting from
errors by the system administrator).
To assign different configEpochs to different nodes at startup was a
task performed naturally by the config conflicts resolution algorithm
(see the Cluster specification). However this works well only for small
clusters or when there are actually just a few collisions, since it is
designed for exceptional cases.
When a large cluster is created hundred of nodes can be at epoch 0, so
the conflict resolution code is slow to provide an unique config to each
node. For this reason this new command was introduced. It can be called
only when a node is totally fresh: no other nodes known, and configEpoch
set to zero, so it is safe even against misuses.
redis-trib will use the new command in order to start the cluster
already setting an incremental unique config to every node.
We should return REDIS_ERR to signal we can't read the configuration
because there is no config file only after checking errno, othewise
we risk to rewrite an existing file that was not accessible for some
other reason.
This was a common source of problems among users.
The solution adopted is not bullet-proof as if the user deletes the
nodes.conf file manually, and starts a new instance with the same
nodes.conf file path, two instances will use the same file. However
following this reasoning the user may drop a nuclear bomb into the
datacenter as well.
adjustOpenFilesLimit() and clusterUpdateSlotsWithConfig() that were
assuming uint64_t is the same as unsigned long long, which is true
probably for all the systems out there that we target, but still GCC
emitted a warning since technically they are two different types.
This is not really an error but something that always happens for
example when creating a new cluster, or if the sysadmin rejoins manually
a node that is already known.
Since useless logs don't help, moved to VERBOSE level.
New config epochs must always be obtained incrementing the currentEpoch,
that is itself guaranteed to be >= the max configEpoch currently known
to the node.
The slave election in Redis Cluster guarantees that slaves promoted to
masters always end with unique config epochs, however failures during
manual reshardings, software bugs and operational errors may in theory
cause two nodes to have the same configEpoch.
This commit introduces a mechanism to eventually always end with different
configEpochs if a collision ever happens.
As a (wanted) side effect, this also ensures that after a new cluster
is created, all nodes will end with a different configEpoch automatically.
By manually modifying nodes configurations in random ways, it is possible
to create the following scenario:
A is serving keys for slot 10
B is manually configured to serve keys for slot 10
A receives an update from B (or another node) where it is informed that
the slot 10 is now claimed by B with a greater configuration epoch,
however A still has keys from slot 10.
With this commit A will put the slot in error setting it in IMPORTING
state, so that redis-trib can detect the issue.
This API originated from the "diskstore" experiment, not for Redis
Cluster itself, so there were legacy/useless things trying to
differentiate between keys that are going to be overwritten and keys
that need to be fetched from disk (preloaded).
All useless with Cluster, so removed with the result of code
simplification.
The code was already correct but it was using that bindaddr[0] is set to
NULL as a side effect of current implementation if no bind address is
configured. This is not guarnteed to hold true in the future.
